|
Post by badbrad on May 21, 2019 6:23:11 GMT -6
Looking at this 2 bottom. Looks like the plow blades are rusted through. Are those parts you can get reasonable at a farm supply store? Or is it not worth the hassle?
|
|
|
Post by badbrad on May 21, 2019 6:24:28 GMT -6
|
|
|
Post by sd51555 on May 21, 2019 10:54:06 GMT -6
I think you've done enough plowin' already.
|
|
|
Post by jbird on May 21, 2019 11:10:12 GMT -6
Fair warning....on the leading debris cutter - you may need to cut part of that frame off to be able to hook up to your tractor. I was given a 2 bottom plow and the frame that supported the leading cutter was further forward than I cared for....so a smoke wrench was in order. It kept hitting my lower lift arm on my hitch.
As for the wear....I have no idea. I didn't/don't plow enough to worry about wearing it out! Biggest thing I looked for was the plow points....that is where the point enters the soil and tend to break/bend/wear the most.
|
|
|
Post by benmnwi on May 21, 2019 11:19:51 GMT -6
I had an old disk that was about that old and replacement/repairs weren't too easy because of wear, rust, etc. Based on that I would assume that any repair or replacement would be more complicated and expensive than on a newer plow.
Is there a reason you're looking at a 2 bottom plow rather than just a spray and disk plan? That's my go-to plan, but my soil is sandy in most areas so that helps. I bought a nice used 3 point 6' John Deere cultivator that I use for breaking new ground and I'm happy how that works in areas that the disk doesn't cut in enough.
|
|
|
Post by badbrad on May 21, 2019 11:30:58 GMT -6
I had an old disk that was about that old and replacement/repairs weren't too easy because of wear, rust, etc. Based on that I would assume that any repair or replacement would be more complicated and expensive than on a newer plow. Is there a reason you're looking at a 2 bottom plow rather than just a spray and disk plan? That's my go-to plan, but my soil is sandy in most areas so that helps. I bought a nice used 3 point 6' John Deere cultivator that I use for breaking new ground and I'm happy how that works in areas that the disk doesn't cut in enough.
I knew that question was coming. LOL
I want to be able to flop it over once in awhile for a couple of reasons. It gets rid of compaction as I keep working that heavy clay. It helps dry the soil out. You lose organic matter I know but I would not mind the capability to flop it over and start from scratch as needed. For the most part I will be spraying and discing
|
|
|
Post by benmnwi on May 21, 2019 12:05:11 GMT -6
Would you have issues using a plow on your ground because of tree roots in areas that were recently cleared? That might be hard on anything, especially an older plow.
If that plow was cheap enough you could just use it until it broke since you could probably get a replacement plow at a decent price off Craigslist or local auctions. There's a farmer by my place in SE MN that uses a moldboard plow every year and has done so for at least 30 years (this was as long as I've been paying attention, but they were probably doing this for the past 100 years). His crops still look as good as the neighboring properties, so I think the organic matter decline isn't too quick by any stretch.
|
|
|
Post by biglakebass on May 21, 2019 12:09:06 GMT -6
Waht about a king kutter middle buster Brad?
We have one and works well.
|
|
|
Post by badbrad on May 21, 2019 12:11:52 GMT -6
Would you have issues using a plow on your ground because of tree roots in areas that were recently cleared? That might be hard on anything, especially an older plow. If that plow was cheap enough you could just use it until it broke since you could probably get a replacement plow at a decent price off Craigslist or local auctions. There's a farmer by my place in SE MN that uses a moldboard plow every year and has done so for at least 30 years (this was as long as I've been paying attention, but they were probably doing this for the past 100 years). His crops still look as good as the neighboring properties, so I think the organic matter decline isn't too quick by any stretch. Catching roots could definitely be a problem for awhile till they break down more. I just want to get one to add to list of implements and options I have. Waiting for the right deal. Not in a big rush.
|
|
|
Post by badbrad on May 21, 2019 12:13:28 GMT -6
Waht about a king kutter middle buster Brad? We have one and works well. How much area do you do with it? Is it pretty slow with one plow blade?
|
|
|
Post by biglakebass on May 21, 2019 12:15:35 GMT -6
we have only used it when we created some plots to bust up roots and get things started.
You can say its slow becuase its one blade, but you wont be using it that often would you?
Its pretty cheap to buy.
|
|
|
Post by biglakebass on May 21, 2019 12:18:06 GMT -6
You do end up with some ruts and clumps to deal with, but just run the disc over it a few times and everything will work out great.
We have hooked rocks and put the tractor to a stop with the tires spinning. Its a pretty strong built item.
|
|
|
Post by batman on May 21, 2019 12:46:59 GMT -6
You are trying to rationalize fucking a fat girl.
|
|
|
Post by badbrad on May 21, 2019 13:46:37 GMT -6
You are trying to rationalize fucking a fat girl. That is a pretty good metaphor. LOL
|
|
|
Post by biglakebass on May 21, 2019 17:55:43 GMT -6
how much area are you talking Brad?
|
|